Linksys MR7500

This router's wan (Internet 5Gbps) port is not visible, and will not function unless ALL first-time installation steps are taken. Follow the installation steps carefully.

Linksys MR7500 is a tri-band 2.4G/5G/6G Wi-Fi 6E router with 4x1Gbase-T ports and a single 1/2.5/5Gbase-T port via an AQC114 chipset.

Supported Versions

While OpenWrt 25.12.x works on this device, you should consider using SNAPSHOT for better support of the 5Gb interface. Carefully follow the instructions in the Installation section below.

Experimental Versions

None at this time.

Hardware Highlights

Installation

As stated above, SNAPSHOT is recommended for better support of the 5Gb interface.

Stable release

Snapshot

Flash instructions (GUI)

Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup. xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo (or the square with a “wireless” icon on some units) to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker. On first login, you may need to reset the password using the Recovery Key on the sticker.
Enter into support mode by clicking on the “CA” link at the bottom of the page.
Open the “Connectivity” menu.
Upload the OpenWrt factory image with the “Choose file” button.
Click start.
Ignore all the prompts and warnings by clicking “yes” in all the popups.
Once the router has booted into OpenWrt, proceed to flashing the WAN port firmware.

Flash instructions (Serial)

This method requires taking the unit apart to access the UART pin header.

1. Installation using serial connection from OEM firmware (default login: root, password: admin):

fw_printenv -n boot_part

In case of 2:

flash_erase /dev/mtd13 0 0
nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin

or in case of 1:

flash_erase /dev/mtd15 0 0
nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin

After first boot install firmware on second partition:

mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel

or:

mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel

2. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive:

dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda

Stop u-boot and run:

usb start && usbboot $loadaddr 0 && bootm $loadaddr

Write firmware to the flash from initramfs:

mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel

and:

mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel

3. Back to the OEM firmware:

mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel

and:

mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel

4. USB recovery: Put the initramfs image on the USB:

dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda

Set u-boot env:

fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

WAN port firmware

While it is possible to copy the file AQR114C.cld to /lib/firmware/marvell (thus avoiding both adding the header and burning to flash), firmware loading from the OpenWrt filesystem is known to be buggy in current builds and may not work. As such, burning to flash is recommended.

By default, the WAN port does not work in OpenWRT. This is due to the existing firmware on the PHY flash being incomplete from factory, and the firmware is not present in linux-firmware, nor is OpenWRT able to ship the firmware blobs due to licencing concerns (see https://lists.openwrt.org/pipermail/openwrt-devel/2024-February/042231.html ).

To fix this, the WAN PHY flash needs to be overwritten with a good firmware image. Instructions to do so are below.

0. Firmware source

The firmware for the WAN port can be obtained as a prebuilt, ready-to-flash image from (https://github.com/user-attachments/files/28231596/AQR-v5.6.5-Cybertan_Divo.zip) OR can be extracted from the OEM firmware following the instructions below.

1. Firmware extraction

If using the ready-to-flash image, skip this step.

To extract the firmware, use unblob (https://unblob.org/installation/) against your backup or the latest latest OEM firmware.

The firmware is located at etc/AQR114C.cld within the squashfs portion of the OEM firmware image.

A header must be added before it can be burned to flash. Use the script from https://github.com/testuser7/aqr_mbn_tool to do so:

aqr_mbn_tool.py -o AQR-v5.6.5-Cybertan_Divo.ethphyfw AQR114C.cld

2. Firmware loading

To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.

To do this, you need to modify u-boot env: With USB recovery (recommended):

fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

and without:

fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

3. Firmware updating

First, copy the file AQR-v5.6.5-Cybertan_Divo.ethphyfw to your router via scp then:

cat /proc/mtd|grep "0:ethphyfw"

should return something like:

mtd9: 00080000 00020000 "0:ethphyfw"

First, take a backup of the partition in case anything goes wrong:

dd if=/dev/mtd9 of=/tmp/ethphyfw.bak

then flash to the mtd partition you see in your results:

mtd erase /dev/mtd9
mtd -n write /tmp/AQR-v5.6.5-Cybertan_Divo.ethphyfw /dev/mtd9

when booting you should see the firmware loading:

[    7.453405] Aquantia AQR114C 90000.mdio-1:08: loading firmware version 'v5.6.5 Cybertan Divo 090221 14:43:44' from 'NVMEM'

Flash Layout

dev:    size   erasesize  name
mtd0: 00180000 00020000 "0:sbl1"
mtd1: 00100000 00020000 "0:mibib"
mtd2: 00380000 00020000 "0:qsee"
mtd3: 00080000 00020000 "0:devcfg"
mtd4: 00080000 00020000 "0:rpm"
mtd5: 00080000 00020000 "0:cdt"
mtd6: 00080000 00020000 "0:appsblenv"
mtd7: 00180000 00020000 "0:appsbl"
mtd8: 00080000 00020000 "0:art"
mtd9: 00080000 00020000 "0:ethphyfw"
mtd10: 00080000 00020000 "u_env"
mtd11: 00040000 00020000 "s_env"
mtd12: 00040000 00020000 "devinfo"
mtd13: 00800000 00020000 "kernel"
mtd14: 04a00000 00020000 "rootfs"
mtd15: 00800000 00020000 "alt_kernel"
mtd16: 04a00000 00020000 "alt_rootfs"
mtd17: 00400000 00020000 "sysdiag"
mtd18: 13d00000 00020000 "syscfg"
mtd19: 00500000 00020000 "app_data"

Upgrading OpenWrt

→ generic.sysupgrade

Debricking

→ generic.debrick

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Switch Ports (for VLANs)

Port	Switch port
LAN 1	lan1
LAN 2	lan2
LAN 3	lan3
LAN 4	lan4
Internet (WAN)	wan

Buttons

→ hardware.button on howto use and configure the hardware button(s).

The Linksys MR7500 has the following buttons:

The events triggered by these buttons haven't been verified yet.

BUTTON	Event
Reset	reset
WPS	wps

Hardware

Info

More info on components:

RAM:	512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash:	512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet:	1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet:	4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1:	6GHz ax 4×4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2:	5GHz ax 2×2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3:	2.4GHz ax 2×2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT:	Bluetooth 5 (CSR8811) - not implemented
LED:	1x RGB status + USB Blue (PWM)

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Opening the case

→ Warranty

Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

Serial

→ port.serial general information about the serial port, serial port cable, etc.

Insert photo of PCB with markings for serial port

The UART is the 5-pin J3 header at the front of the board next to the blue power LED.

pinout, GND is side nearest power LED: 

GND x TX RX x

Serial connection parameters for Linksys MR7500	115200, 8N1, 3.3V

JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

→ bootloader

Hardware mods

None so far.

Bootlogs

OEM bootlog

S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00100-IPQ60xxLZB-1 S - IMAGE_VARIANT_STRING=IPQ6018LA S - OEM_IMAGE_VERSION_STRING=crm-ubuntu124 S - Boot Interface: NAND S - Secure Boot: Off S - Boot Config @ 0x000a602c = 0x000002e5 S - JTAG ID @ 0x000a607c = 0x001260e1 S - OEM ID @ 0x000a6080 = 0x00000000 S - Serial Number @ 0x000a4128 = 0xb7a74ff7 S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000 S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000 S - Feature Config Row 0 @ 0x000a4130 = 0x0000000008200001 S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e80383000009 S - PBL Patch Ver: 1 S - I-cache: On S - D-cache: On B - 3413 - PBL, Start B - 592 - bootable_media_detect_entry, Start B - 4339 - bootable_media_detect_success, Start B - 5207 - elf_loader_entry, Start B - 5380 - auth_hash_seg_entry, Start B - 7847 - auth_hash_seg_exit, Start B - 8346 - elf_segs_hash_verify_entry, Start B - 103710 - elf_segs_hash_verify_exit, Start B - 107899 - auth_xbl_sec_hash_seg_entry, Start B - 108045 - auth_xbl_sec_hash_seg_exit, Start B - 114598 - xbl_sec_segs_hash_verify_entry, Start B - 114599 - xbl_sec_segs_hash_verify_exit, Start B - 115528 - PBL, End B - 97447 - SBL1, Start B - 240340 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4 B - 242780 - clock_init, Start D - 3812 - clock_init, Delta B - 252418 - boot_flash_init, Start D - 27267 - boot_flash_init, Delta B - 281911 - sbl1_ddr_set_default_params, Start D - 244 - sbl1_ddr_set_default_params, Delta B - 288530 - boot_config_data_table_init, Start D - 5002 - boot_config_data_table_init, Delta - (575 Bytes) B - 298717 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:0,Subtype:2 B - 303200 - Image Load, Start D - 6619 - OEM_MISC Image Loaded, Delta - (0 Bytes) B - 312564 - Image Load, Start D - 5063 - PMIC Image Loaded, Delta - (0 Bytes) B - 320433 - sbl1_ddr_set_params, Start B - 325404 - CPR configuration: 0x366 B - 328607 - Pre_DDR_clock_init, Start D - 213 - Pre_DDR_clock_init, Delta D - 0 - sbl1_ddr_set_params, Delta B - 362767 - Image Load, Start D - 518 - APDP Image Loaded, Delta - (0 Bytes) B - 381280 - Image Load, Start D - 488 - QTI_MISC Image Loaded, Delta - (0 Bytes) B - 383812 - Image Load, Start D - 854 - Auth Metadata D - 702 - Segments hash check D - 24004 - QSEE Dev Config Image Loaded, Delta - (37162 Bytes) B - 409645 - Image Load, Start D - 6527 - Auth Metadata D - 10400 - Segments hash check D - 371002 - QSEE Image Loaded, Delta - (1435060 Bytes) B - 781166 - Image Load, Start D - 732 - Auth Metadata D - 1007 - Segments hash check D - 38521 - RPM Image Loaded, Delta - (102948 Bytes) B - 821029 - Image Load, Start D - 763 - Auth Metadata D - 3233 - Segments hash check D - 139172 - APPSBL Image Loaded, Delta - (568944 Bytes) B - 988840 - SBL1, End D - 891790 - SBL1, Delta S - Flash Throughput, 4000 KB/s (2144689 Bytes, 475972 us) S - Core 0 Frequency, 800 MHz S - DDR Frequency, 466 MHz U-Boot 2016.01 (Dec 10 2020 - 22:29:27 +0800) CBT U-Boot ver: 1.0.12 ([IPQ6018].[SPF11.2 CS]) DRAM: smem ram ptable found: ver: 2 len: 4 512 MiB NAND: ONFI device found ID = 1590acad Vendor = ad Device = ac qpic_nand: changing oobsize to 64 from 128 bytes SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 512 MiB MMC: sdhci: Node Not found, skipping initialization PCI Link Intialized In: serial@78B1000 Out: serial@78B1000 Err: serial@78B1000 machid: 8030002 eth1 MAC Address from ART is not valid eth2 MAC Address from ART is not valid eth3 MAC Address from ART is not valid eth4 MAC Address from ART is not valid eth5 MAC Address from ART is not valid Setting bus to 0 Valid chip addresses: Updating boot_count ... done Saving Environment to NAND... Erasing NAND... Erasing at 0xae0000 -- 100% complete. Writing to NAND... OK Hit any key to stop autoboot: 0 NAND read: device 0 offset 0xa00000, size 0x80000 524288 bytes read: OK CRC check good on phy fw file (0x62C1) PHYFW:Loading IRAM...........done. PHYFW:Loading DRAM..............done. phy fw image load good CRC-16 matches (0x9CDE) starting USB... USB0: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus 0 for devices... 1 USB Device(s) found USB1: Register 1000140 NbrPorts 1 Starting the controller USB XHCI 1.10 scanning bus 1 for devices... 1 USB Device(s) found ** Bad device usb 0 ** NAND read: device 0 offset 0x5d80000, size 0x800000 8388608 bytes read: OK ## Loading kernel from FIT Image at 44000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e4 Data Size: 4716938 Bytes = 4.5 MiB Architecture: ARM OS: Linux Load Address: 0x41008000 Entry Point: 0x41008000 Hash algo: crc32 Hash value: 426554be Hash algo: sha1 Hash value: 8b46f58c2c9c1e1af9a9bfc87545170696e10fb2 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 44000000 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM OpenWrt Divo device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x4447fba0 Data Size: 77496 Bytes = 75.7 KiB Architecture: ARM Hash algo: crc32 Hash value: 09be970a Hash algo: sha1 Hash value: 07c2df79c4fd1452c69eac5ea7759a8f9505521e Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x4447fba0 Uncompressing Kernel Image ... OK Loading Device Tree to 484ea000, end 484ffeb7 ... OK Using machid 0x8030002 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.60 (root@ip-10-0-0-174) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 998fe11+r49254) ) #1 SMP PREEMPT Mon Jun 2 16:59:57 PDT 2025 [ 0.000000] CPU: ARMv7 Processor [51af8014] revision 4 (ARMv7), cr=10c0383d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C3 [ 0.000000] Ignoring memory range 0x40000000 - 0x41000000 [ 0.000000] Reserved memory: created DMA memory pool at 0x50a00000, size 9 MiB [ 0.000000] Reserved memory: initialized node dma_pool0@50A00000, compatible id shared-dma-pool [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 11 pages/cpu @9eb37000 s15424 r8192 d21440 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 97956 [ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait swiotlb=1 coherent_pool=2M [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 379632K/396288K available (7352K kernel code, 461K rwdata, 2204K rodata, 1024K init, 474K bss, 16656K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0x9f800000 - 0xff800000 (1536 MB) [ 0.000000] lowmem : 0x80000000 - 0x9f000000 ( 496 MB) [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [ 0.000000] .text : 0x80008000 - 0x80a552ec (10549 kB) [ 0.000000] .init : 0x80b00000 - 0x80c00000 (1024 kB) [ 0.000000] .data : 0x80c00000 - 0x80c73620 ( 462 kB) [ 0.000000] .bss : 0x80c76000 - 0x80cecbd8 ( 475 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000016] Switching to timer-based delay loop, resolution 41ns [ 0.000463] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000475] pid_max: default: 32768 minimum: 301 [ 0.000564] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000573] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001074] Initializing cgroup subsys io [ 0.001088] Initializing cgroup subsys memory [ 0.001110] Initializing cgroup subsys devices [ 0.001125] Initializing cgroup subsys freezer [ 0.001134] Initializing cgroup subsys net_cls [ 0.001143] Initializing cgroup subsys pids [ 0.001165] CPU: Testing write buffer coherency: ok [ 0.001541] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001589] Setting up static identity map for 0x41100000 - 0x41100058 [ 0.054085] MSM Memory Dump base table set up [ 0.054107] MSM Memory Dump apps data table set up [ 0.090214] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.120202] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.150236] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.150290] Brought up 4 CPUs [ 0.150308] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.150315] CPU: All CPU(s) started in SVC mode. [ 0.170798] VFP support v0.3: implementor 51 architecture 3 part 40 variant 3 rev 4 [ 0.171094] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.171116] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.171462] pinctrl core: initialized pinctrl subsystem [ 0.172504] NET: Registered protocol family 16 [ 0.173612] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.200075] cpuidle: using governor ladder [ 0.230094] cpuidle: using governor menu [ 0.230339] NET: Registered protocol family 42 [ 0.247302] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.250591] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.260266] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.260274] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.262005] Read of property:soc_version_minor from node failed [ 0.262014] CPU: IPQ6018, SoC Version: 1.0 [ 0.262864] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.264173] IPC logging disabled [ 0.264180] IPC logging disabled [ 0.264184] IPC logging disabled [ 0.264189] IPC logging disabled [ 0.264193] IPC logging disabled [ 0.264416] sps:sps is ready. [ 0.300954] socinfo_select_format: Unsupported format v0.13. Falling back to v0.12. [ 0.300977] socinfo_print: v0.12, id=402, ver=1.0, raw_id=294, raw_ver=0, hw_plat=8, hw_plat_ver=196608 [ 0.300977] accessory_chip=0, hw_plat_subtype=2, pmic_model=0, pmic_die_revision=0 foundry_id=2 serial_number=3081195511 num_pmics=0 chip_family=0x66 raw_device_family=0x2 raw_device_number=0x17 [ 0.301930] usbcore: registered new interface driver usbfs [ 0.301984] usbcore: registered new interface driver hub [ 0.302049] usbcore: registered new device driver usb [ 0.302141] pps_core: LinuxPPS API ver. 1 registered [ 0.302148] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.302172] PTP clock support registered [ 0.304224] rpmsg_dev_probe: No pm domain [ 0.305590] Bluetooth: Core ver 2.21 [ 0.305623] NET: Registered protocol family 31 [ 0.305630] Bluetooth: HCI device and connection manager initialized [ 0.305641] Bluetooth: HCI socket layer initialized [ 0.305651] Bluetooth: L2CAP socket layer initialized [ 0.305675] Bluetooth: SCO socket layer initialized [ 0.305949] clocksource: Switched to clocksource arch_sys_counter [ 0.308720] NET: Registered protocol family 2 [ 0.309347] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.309401] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.309476] TCP: Hash tables configured (established 4096 bind 4096) [ 0.309515] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.309538] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.309689] NET: Registered protocol family 1 [ 0.310901] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available [ 0.319220] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.319241] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.323066] Key type asymmetric registered [ 0.323080] Asymmetric key parser 'x509' registered [ 0.323115] io scheduler noop registered [ 0.323128] io scheduler deadline registered (default) [ 0.328644] ipq4019_pwm_probe: ipq4019_pwm_config set pwm0 duty_cycle=625000, periods=1250000 [ 0.349613] 20000000.pci supply vdda not found, using dummy regulator [ 0.349657] 20000000.pci supply vdda_phy not found, using dummy regulator [ 0.349710] 20000000.pci supply vdda_refclk not found, using dummy regulator [ 0.350211] PCI host bridge /soc/pci@20000000 ranges: [ 0.350238] IO 0x20200000..0x202fffff -> 0x20200000 [ 0.350253] MEM 0x20300000..0x302fffff -> 0x20300000 [ 0.597499] qcom-pcie 20000000.pci: link up [ 0.597657] qcom-pcie 20000000.pci: PCI host bridge to bus 0000:00 [ 0.597670] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.597684] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x20200000-0x202fffff]) [ 0.597696] pci_bus 0000:00: root bus resource [mem 0x20300000-0x302fffff] [ 0.598048] PCI: bus0: Fast back to back transfers disabled [ 0.598060] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.599045] PCI: bus1: Fast back to back transfers disabled [ 0.599108] pci 0000:00:00.0: BAR 8: assigned [mem 0x20400000-0x205fffff] [ 0.599122] pci 0000:00:00.0: BAR 9: assigned [mem 0x20600000-0x207fffff 64bit pref] [ 0.599134] pci 0000:00:00.0: BAR 0: assigned [mem 0x20300000-0x20300fff 64bit] [ 0.599150] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] [ 0.599164] pci 0000:01:00.0: BAR 0: assigned [mem 0x20400000-0x205fffff 64bit] [ 0.599215] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.599225] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 0.599237] pci 0000:00:00.0: bridge window [mem 0x20400000-0x205fffff] [ 0.599249] pci 0000:00:00.0: bridge window [mem 0x20600000-0x207fffff 64bit pref] [ 0.599298] PCIe: RC0 enabled during bootup [ 0.599796] MDSS QPIC HW Base phy_Address=0x7980000 virt=9fb40000 [ 0.600183] mdss_qpic_panel_probe: Panel Name = qpic lcd panel [ 0.601986] mdss_fb_register: FrameBuffer[0] 800x480 registered successfully! [ 0.607388] global timer is null [ 0.607844] NET: Registered protocol family 27 [ 0.607853] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 0.607999] msm_rpm_log_probe: OK [ 0.608337] msm-dcc b3000.dcc: DCC XPU is not specified [ 0.608578] msm-dcc b3000.dcc: jiffies_64: 0xffff8b0c, cntvct_64: 0x30bafbcd [ 0.608590] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0x9fb16004) [ 0.608600] msm-dcc b3000.dcc: gcnt_lo: 0x30bafe15(0x9fb16000) [ 0.609607] TZ SMMU State: SMMU Stage2 Enabled [ 0.609661] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set [ 0.609871] rpmsg_dev_probe: No pm domain [ 0.610766] msm_serial 78b0000.serial: msm_serial: detected port #1 [ 0.610800] msm_serial 78b0000.serial: uartclk = 24000000 [ 0.610832] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 20, base_baud = 1500000) is a MSM [ 0.611147] msm_serial 78b1000.serial: msm_serial: detected port #0 [ 0.611177] msm_serial 78b1000.serial: uartclk = 1843199 [ 0.611204] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115199) is a MSM [ 0.611220] msm_serial: console setup on port #0 [ 1.576250] console [ttyMSM0] enabled [ 1.581293] msm_serial: driver initialized [ 1.584829] msm_serial_hsl_init: driver initialized [ 1.597974] brd: module loaded [ 1.603412] loop: module loaded [ 1.604051] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 1.607060] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 0, 0 [ 1.613389] QPIC controller hw version Major:1, Minor:5 [ 1.619352] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xac [ 1.624105] nand: ONFI 10-Compliant Hynix H27S4G8F2EDA-BC [ 1.630732] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128 [ 1.636098] 20 ofpart partitions found on MTD device qcom_nand.0 [ 1.643462] Creating 20 MTD partitions on "qcom_nand.0": [ 1.649730] 0x000000000000-0x000000180000 : "0:SBL1" [ 1.657273] 0x000000180000-0x000000280000 : "0:MIBIB" [ 1.661683] 0x000000280000-0x000000600000 : "0:QSEE" [ 1.669033] 0x000000600000-0x000000680000 : "0:DEVCFG" [ 1.671214] 0x000000680000-0x000000700000 : "0:RPM" [ 1.676204] 0x000000700000-0x000000780000 : "0:CDT" [ 1.680934] 0x000000780000-0x000000800000 : "0:APPSBLENV" [ 1.685720] 0x000000800000-0x000000980000 : "0:APPSBL" [ 1.692251] 0x000000980000-0x000000a00000 : "0:ART" [ 1.696356] 0x000000a00000-0x000000a80000 : "0:ETHPHYFW" [ 1.701125] 0x000000a80000-0x000000b00000 : "u_env" [ 1.706713] 0x000000b00000-0x000000b40000 : "s_env" [ 1.711072] 0x000000b40000-0x000000b80000 : "devinfo" [ 1.715938] 0x000000b80000-0x000005d80000 : "kernel" [ 1.797896] 0x000001380000-0x000005d80000 : "rootfs" [ 1.867946] mtd: device 14 (rootfs) set to be root filesystem [ 1.868276] mtdsplit: no squashfs found in "rootfs" [ 1.872669] 0x000005d80000-0x00000af80000 : "alt_kernel" [ 1.954791] 0x000006580000-0x00000af80000 : "alt_rootfs" [ 2.024751] 0x00000af80000-0x00000b380000 : "sysdiag" [ 2.029304] 0x00000b380000-0x00001f080000 : "syscfg" [ 2.204558] random: nonblocking pool is initialized [ 2.326860] 0x00001f080000-0x00001f580000 : "app_data" [ 2.333348] libphy: Fixed MDIO Bus: probed [ 2.774199] qca-mdio 90000.mdio: Could not find phy-reset-gpio [ 2.774340] libphy: qca_mdio: probed [ 2.780480] qca-mdio 90000.mdio: qca-mdio driver was registered [ 2.782790] PPP generic driver version 2.4.2 [ 2.788452] NET: Registered protocol family 24 [ 2.792804] PPTP driver version 0.8.5 [ 2.797245] cnss: INFO: IPC Logging is disabled! [ 2.800878] cnss[27]: INFO: Disabling regdb support for QCN9000_PCI0 [ 2.805714] cnss[27]: INFO: Platform driver probed successfully. plat 9df58010 tgt 0x1104 [ 2.812147] cnss[2]: INFO: Disabling regdb support for QCA6018 [ 2.820063] cnss[2]: INFO: Platform driver probed successfully. plat 9dee0010 tgt 0xfffd [ 2.826043] cnss[27]: INFO: PCI device 9dd30000 probed successfully [ 2.834247] dummy_hcd dummy_hcd.0: USB Host+Gadget Emulator, driver 02 May 2005 [ 2.839880] dummy_hcd dummy_hcd.0: Dummy host controller [ 2.847161] dummy_hcd dummy_hcd.0: new USB bus registered, assigned bus number 1 [ 2.853350] hub 1-0:1.0: USB hub found [ 2.860117] hub 1-0:1.0: 1 port detected [ 2.864240] i2c /dev entries driver [ 2.896444] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 2.896484] Bluetooth: HCI UART driver ver 2.3 [ 2.903939] Bluetooth: HCI UART protocol H4 registered [ 2.908213] Bluetooth: HCI UART protocol BCSP registered [ 2.913315] Bluetooth: HCI UART protocol ATH3K registered [ 2.918872] usbcore: registered new interface driver btusb [ 2.924524] sdhci: Secure Digital Host Controller Interface driver [ 2.929477] sdhci: Copyright(c) Pierre Ossman [ 2.935629] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.940409] sdhci_msm 7804000.sdhci_sd: sdhci_msm_probe: ICE device is not enabled [ 2.945842] sdhci_msm 7804000.sdhci_sd: Got SD LDO GPIO #66 [ 3.053202] sdhci_msm 7804000.sdhci_sd: No vreg data found for vdd [ 3.053231] sdhci_msm 7804000.sdhci_sd: No vreg data found for vdd-io [ 3.069090] sdhci_msm 7804000.sdhci_sd: No vmmc regulator found [ 3.069116] sdhci_msm 7804000.sdhci_sd: Add host failed (-517) [ 3.075499] [ 3.075499] Version Rollback Feature Disabled [ 3.080304] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x08b04000 [ 3.085531] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x08b04000 [ 3.101440] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x08b04000 [ 3.115910] sps:BAM 0x08b04000 is registered.[ 3.124683] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss [ 3.126691] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available [ 3.136367] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000 [ 3.141956] coresight-csr 6001000.csr: CSR initialized [ 3.149688] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000 [ 3.154640] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000 [ 3.162200] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000 [ 3.169577] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000 [ 3.176951] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000 [ 3.184324] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000 [ 3.191713] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000 [ 3.199089] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000 [ 3.206476] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000 [ 3.213831] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000 [ 3.221236] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000 [ 3.228607] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000 [ 3.235992] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000 [ 3.243354] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000 [ 3.250760] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000 [ 3.258130] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000 [ 3.265493] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000 [ 3.273009] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000 [ 3.280391] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000 [ 3.287811] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000 [ 3.295213] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000 [ 3.302555] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06064000 [ 3.309592] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06064000 [ 3.325284] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06064000 [ 3.339793] sps:BAM 0x06064000 is registered.[ 3.346792] coresight-tmc 6048000.tmc: TMC initialized [ 3.350872] coresight-tmc 6047000.tmc: TMC initialized [ 3.356027] coresight-funnel 6041000.funnel: FUNNEL initialized [ 3.361026] coresight-funnel 6100000.funnel: FUNNEL initialized [ 3.366865] coresight-funnel 6130000.funnel: FUNNEL initialized [ 3.372746] coresight-funnel 6120000.funnel: FUNNEL initialized [ 3.378679] coresight-funnel 61a1000.funnel: FUNNEL initialized [ 3.385224] coresight-etm4x 619c000.etm: ETM 4.0 initialized [ 3.390896] coresight-etm4x 619d000.etm: ETM 4.0 initialized [ 3.396833] coresight-etm4x 619e000.etm: ETM 4.0 initialized [ 3.402510] coresight-etm4x 619f000.etm: ETM 4.0 initialized [ 3.407701] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized [ 3.413452] coresight-stm 6002000.stm: STM initialized [ 3.422177] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000 [ 3.425838] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized [ 3.433913] u32 classifier [ 3.441001] input device check on [ 3.443504] Actions configured [ 3.447286] Netfilter messages via NETLINK v0.30. [ 3.450564] nfnl_acct: registering with nfnetlink. [ 3.455356] nf_conntrack version 0.5.0 (5931 buckets, 23724 max) [ 3.460452] ctnetlink v0.93: registering with nfnetlink. [ 3.466255] nf_conntrack_rtsp v0.7 loading [ 3.471520] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net> [ 3.475393] nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org> [ 3.482230] xt_time: kernel timezone is -0000 [ 3.489106] ip_set: protocol 6 [ 3.493709] gre: GRE over IPv4 demultiplexor driver [ 3.496479] ip_gre: GRE over IPv4 tunneling driver [ 3.502406] nf_nat_rtsp v0.7 loading [ 3.506224] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.510026] arp_tables: (C) 2002 David S. Miller [ 3.515970] NET: Registered protocol family 10 [ 3.520682] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.524306] sit: IPv6 over IPv4 tunneling driver [ 3.530581] ip6_gre: GRE over IPv6 tunneling driver [ 3.534706] NET: Registered protocol family 17 [ 3.538789] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.543289] Bridge firewalling registered [ 3.556222] Ebtables v2.0 registered [ 3.560118] Bluetooth: RFCOMM TTY layer initialized [ 3.563565] Bluetooth: RFCOMM socket layer initialized [ 3.568188] Bluetooth: RFCOMM ver 1.11 [ 3.573378] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.577120] Bluetooth: BNEP filters: protocol multicast [ 3.582576] Bluetooth: BNEP socket layer initialized [ 3.587566] l2tp_core: L2TP core driver, V2.0 [ 3.592733] l2tp_netlink: L2TP netlink interface [ 3.597025] 8021q: 802.1Q VLAN Support v1.8 [ 3.602495] Registering SWP/SWPB emulation handler [ 3.606967] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 3.612236] sdhci_msm 7804000.sdhci_sd: sdhci_msm_probe: ICE device is not enabled [ 3.617750] sdhci_msm 7804000.sdhci_sd: Got SD LDO GPIO #66 [ 3.725308] sdhci_msm 7804000.sdhci_sd: No vreg data found for vdd [ 3.725336] sdhci_msm 7804000.sdhci_sd: No vreg data found for vdd-io [ 3.741193] sdhci_msm 7804000.sdhci_sd: No vmmc regulator found [ 3.786069] mmc0: SDHCI controller on 7804000.sdhci_sd [7804000.sdhci_sd] using ADMA 64-bit [ 3.786195] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 3.793397] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 3.800531] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2 [ 3.807124] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 3.814771] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 3.822297] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 3.831428] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 675000 uV [ 3.838376] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 787500 uV [ 3.848359] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 850000 uV [ 3.858167] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 900000 uV [ 3.868014] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 571, quot_offset[ 7]= 0 [ 3.877791] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 755, quot_offset[ 7]= 180 [ 3.888640] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]= 851, quot_offset[ 7]= 95 [ 3.899577] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]= 919, quot_offset[ 7]= 65 [ 3.910769] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 3.923062] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz [ 3.928869] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 864000 KHz [ 3.936674] ubi0: attaching mtd16 [ 4.322987] ubi0: scanning is finished [ 4.329366] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 34, need 80 [ 4.329705] ubi0: attached mtd16 (name "alt_rootfs", size 74 MiB) [ 4.338601] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.344842] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.351624] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.358477] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0 [ 4.365242] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.371499] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 2094997041 [ 4.378534] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 34 [ 4.387826] ubi0: background thread "ubi_bgt0d" started, PID 139 [ 4.407926] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0 [ 4.407995] hctosys: unable to open rtc device (rtc0) [ 4.422250] VFS: Mounted root (squashfs filesystem) readonly on device 31:20. [ 4.423387] Freeing unused kernel memory: 1024K (80b00000 - 80c00000) ********************************************************************************* _ _ __ _ __ _____ __ __ _____ | | | || \ | | / // ____]\ \ / // ____]TM | | | || \ | | / /| (___ \ V /| (____ | | | || |\ \| |\ \ \____ \ \ / \____ \ | |_____ | || | \ | \ \ ____) | | | ____) | |_______||_||_| \__| \_\[____ / |_| [_____/ (c) 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. Booting divo (firmware version 1.1.12.216649) ********************************************************************************* [utopia][init] System Initialization [utopia][init] Creating /proc [utopia][init] Creating /sys [utopia][init] Creating /dev [utopia][init] Creating /tmp [utopia][init] Allocating 60M for /tmp [utopia][init] Prepairing /dev/pts [utopia][init] Setting /tmp and /var permissions [utopia][init] Starting udev.. Attempting mount of ubifs syscfg partition UBI device number 1, total 2536 LEBs (322011136 bytes, 307.1 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [utopia][init] Using persistent syscfg data from /var/config/syscfg [utopia][init] Starting system logging [utopia][init] Starting sysevent subsystem [utopia][init] Checking HW version...XB [utopia][init] Starting blue ... combo_pulse(blue)(1500) XB [utopia][init] Checking HW version...XB [utopia][init] Enabling DesignWare USB3 DRD Core drivers [utopia][init] Loading QCA Ethernet, NSS and GMAC drivers net.netfilter.nf_conntrack_acct = 1 [utopia][init] Late loading usb drivers load AQR fw............. remove loading AQR fw in uboot... SSDK Init OK! operation done. SSDK Init OK! operation done. SSDK Init OK! operation done. SSDK Init OK! operation done. sh: =: argument expected [utopia][init] Setting any unset system values to default [utopia][init] PRODUCT.TYPE (production) [utopia][init] no persistence config file (/var/config/pstcfg) found setting up MAC addresses for all interface based on 80:69:1A:BF:21:9A NTP Servers do not need to be updated [utopia][init][default_overwriting] default_overwriting file (/etc/default_overwriting) found, processing ... [utopia][init][default_overwriting] config_version in syscfg:[1] [utopia][init][default_overwriting] config_version in default_overwriting:[1] [utopia][init][default_overwriting] (update once) found (TZ=HKT-8), but config_version is <= than syscfg, skip [utopia][init][default_overwriting] (update once) found (auto_dst=2), but config_version is <= than syscfg, skip [utopia][init][default_overwriting] (update once) found (wan_auto_detect_enable=0), but config_version is <= than syscfg, skip [utopia][init] syscfg loaded removing tmp file SSDK Init OK! operation done. SSDK Init OK![Ethernet Type]:0x0 operation done. SSDK Init OK! operation done. SSDK Init OK! operation done. checking for interactive script start up... no user scheduled tasks found... senq running /etc/init.d/service_senq.sh Starting in mode 0 1970-01-01 00:00:23: node-mode running Good block at 0x00000000 Updating BootCount Page[61]:1E800 ... Done [utopia][init] LAN Ports LED settings attempting to sync sysinfo.cgi auth credentials [utopia][init] Loading Buttons drivers [utopia][init] Setup link to WiFi firmware and board data (EU) [utopia][init] Multi-region is not supported or not enabled [utopia][init] Cert region: EU [utopia][init] Using EU region for WiFi firmware and board data [utopia][init] Load WiFi cal data from MTD(mtd8) to FS. 65536+0 records in 65536+0 records out 65536 bytes (64.0KB) copied, 0.196631 seconds, 325.5KB/s 131072+0 records in 131072+0 records out 131072 bytes (128.0KB) copied, 0.333994 seconds, 383.2KB/s Size of caldata_1.bin = 131072 bytes. ### caldata_1.bin size is correct ### 131072+0 records in 131072+0 records out 131072 bytes (128.0KB) copied, 0.330107 seconds, 387.8KB/s Size of caldata_1.bin = 131072 bytes. ### caldata_2.bin size is correct ### [utopia][init] Loading WLAN drivers /bin/sh: can't open '/etc/rc.common' [utopia][init] Loading QCA Enhanced Connection manager net.bridge.bridge-nf-call-ip6tables = 1 net.bridge.bridge-nf-call-iptables = 1 dev.nss.general.redirect = 1 [utopia][init] Initializing BTLE interface [utopia][init] Bluetooth Mac Address: 80 69 1A BF 21 9A [utopia][init] Cert Region: EU [utopia][init] BT PSR: /etc/pb-234-csr8x11-rev2.psr Loading PSKEY_HCI_LMP_LOCAL_VERSION ... done Loading PSKEY_LMP_REMOTE_VERSION ... done Loading 0x212c ... done Loading 0x212d ... done Loading 0x212e ... done Loading 0x212f ... done Loading 0x2130 ... done Loading 0x2131 ... done Loading 0x2132 ... done Loading 0x2133 ... done Loading 0x2134 ... done Loading 0x2135 ... done Loading 0x2136 ... done Loading 0x2137 ... done Loading 0x220b ... done Loading 0x222b ... done Loading 0x222c ... done Loading 0x2139 ... done Loading 0x213a ... done Loading 0x213b ... done Loading PSKEY_LC_MAX_TX_POWER ... done Loading PSKEY_HOST_INTERFACE ... done Loading 0x01ea ... done Loading PSKEY_ANA_FREQ ... done Loading PSKEY_ANA_FTRIM ... done Loading 0x22c8 ... done Device setup complete [utopia][init] BTLE interface ready to use inserting fpbypass.ko for QCA attempting to sync sysinfo.cgi auth credentials adding group for lldpd user /dev/mem opened. Memory mapped at address 0x76f85000. Value at address 0x3A001010 (0x76f85010): 0xB00E6060 Written 0xB00E6070; readback 0xB00E6070 /dev/mem opened. Memory mapped at address 0x76f30000. Value at address 0x3A001210 (0x76f30210): 0xB00E6060 Written 0xB00E6070; readback 0xB00E6070 /dev/mem opened. Memory mapped at address 0x76fc0000. Value at address 0x3A001410 (0x76fc0410): 0xB00E6060 Written 0xB00E6070; readback 0xB00E6070 /dev/mem opened. Memory mapped at address 0x76f9a000. Value at address 0x3A001610 (0x76f9a610): 0xB00E6060 Written 0xB00E6070; readback 0xB00E6070 Wed Feb 4 16:15:00 UTC 2026 (none) login: wan, sysevent received: wan-start Starting devicedb ... lldpd event lan_ipaddr 10.234.1.1 received. lldpd event lldpd-start received. DeviceDB database version 3 killall: lldpd: no process killed Options: Daemonize : yes Server UDS Path : /tmp/devicedb/server_link Database File : /tmp/devicedb/devicedb.db DB Transient File : /tmp/devicedb/transient.db DeviceDB Daily Backup Cron job created No TopoDB persistence data to import TopoDB data not imported setting root_accessible to 0 by default setting root_accessible to 0 by default mosquitto aborting: not Master lldp updating callback scripts service_guardian.sh is called with lan-status Entry tsmb lan-status, 1 ping6: sendto: Network is unreachable RTNETLINK answers: Device or resource busy 2026-02-04T16:15:03 [WARN/main] another instance is running, please stop it 2026-02-04T16:15:03 [CRIT/main] giving up >> LLDPD - ERROR STARTING DAEMON ARP agent not started: not in master mode. lldpd event lldp::root_accessible 0 received. backhaul_switching status event backhaul::media 0 received on backhaul_switching_mgr Backhaul media 0 received, but wifi status is not started. Will do backhaul check later Starting ddd_ethernet_agent ... [/etc/init.d/service_ntpclient.sh] Set TZ default already done, ignore. lldpd event ETH::port_1_status up received. Lighttpd Model Base: MR7500 [utopia] Not setting ppp_clamp_mtu Generating Rainier lighttpd config Build temporary www configuration directory: nss_build_bypass is called with lan-started TSLIIHauhEfGE Power cycle Ethernet ports. conntrack_parse running creating conntrack cron job ARP agent not started: not in master mode. lldpd event ETH::port_2_status down received. Registering Service myrouter._http._tcp.local port 80 lldpd event ETH::port_3_status down received. Got a reply for myrouter._http._tcp.local.: Name now registered and active wifi, sysevent received: lan-started (Wed Feb 4 16:15:11 GMT 2026) wifi, service_start() [utopia][init] Loading GMAC and WLAN drivers [utopia][init] Creating wifi devices Multi-region is not supported or not enabled SKU is MR7500-EU mosquitto aborting: not Master Entry tsmb lan-status, 1 service_guardian.sh is called with lan-status smart connect client, generating client device data wifi, wifi_physical_start(ath0) dev.nss.n2hcfg.n2h_high_water_core0 = 8704 dev.nss.n2hcfg.extra_pbuf_core0 = 3200000 dev.nss.n2hcfg.n2h_high_water_core0 = 31648 sysctl: short write lldpd event ETH::port_4_status down received. lldpd event ETH::port_5_status up received. dev.nss.n2hcfg.n2h_queue_limit_core0 = 256 ath0 No such device subscriber running /etc/init.d/service_subscriber.sh subscriber-stop NULL MODE: 0 killall: omsgd: no process killed Auto channel killall: configure_me_monitor.sh: no process killed rm: can't remove '/var/run/configure_me_monitor.sh.pid': No such file or directory wifi, wifi_virtual_start(ath0) Not ready for JNAP. Sleeping for 15 seconds... wifi, wifi_user_start(ath0) backhaul_switching status event system_state-normal received wifi_user, ath0 TxBF enabled wifi_user, ath0 MU-MIMO enabled wifi, primary AP: ath0 is up (Wed Feb 4 16:15:21 GMT 2026) wifi, wifi_guest_start(ath0) wifi, guest ath2 is disabled, do not start wifi guest wifi, smart::mode is unconfigured do not start smart connect setup and config wifi wifi, wifi_physical_start(ath1) [utopia] Not setting ppp_clamp_mtu on dslite protocol dev.nss.n2hcfg.n2h_high_water_core0 = 31648 sysctl: short write dev.nss.n2hcfg.n2h_high_water_core0 = 31648 sysctl: short write dev.nss.n2hcfg.n2h_queue_limit_core0 = 256 ath1 No such device List Flushed Following channels are blocked from Channel selection algorithm [116] [120] [124] [128] List Flushed Following channels are blocked from Channel selection algorithm [52] [56] [60] [64] [100] [104] [108] [112] [116] [120] [124] [128] [132] [136] [140] nss_build_bypass is called with ipv4_wan_ipaddr lldpd event ipv4_wan_ipaddr 0.0.0.0 received. getting geoip information for 0.0.0.0 Auto channel % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spwifi, wifi_virtual_start(ath1) ent Left Speed 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (6) Could not resolve: freegeoip.net (Could not contact DNS servers) wifi, wifi_user_start(ath1) Entry tsmb tsmb-stop, 1 wifi_user, ath1 TxBF enabled wifi_user, ath1 MU-MIMO enabled wifi, primary AP: ath1 is up (Wed Feb 4 16:15:26 GMT 2026) wifi, wifi_guest_start(ath1) wifi, guest ath3 is disabled, do not start wifi guest wifi, wifi_physical_start(ath20) dev.nss.n2hcfg.n2h_high_water_core0 = 31648 sysctl: short write dev.nss.n2hcfg.n2h_high_water_core0 = 31648 sysctl: short write dev.nss.n2hcfg.n2h_queue_limit_core0 = 256 ath20 No such device fastpath, sysevent received: qos_enabled net.bridge.bridge-nf-call-ip6tables = 1 net.bridge.bridge-nf-call-iptables = 1 dev.nss.general.redirect = 1 Auto channel wifi, wifi_virtual_start(ath20) wifi, wifi_user_start(ath20) lldpd event ETH::port_1_status down received. nss_build_bypass is called with build_bypass killall: mdns_lookup: no process killed wifi_user, ath20 TxBF enabled LookUpMaster call OK. mDNS lookup is on going... wifi_user, ath20 MU-MIMO enabled smart_connect, sysevent received: wifi-status starting wifi, primary AP: ath20 is up (Wed Feb 4 16:15:31 GMT 2026) wifi, wifi_guest_start(ath20) wifi, guest ath6 is disabled, do not start wifi guest wifi, start_hostapd() 2026-02-04 16:15:31: Setting defaults lldpd event ETH::port_1_status up received. wifi, start hostapd (Wed Feb 4 16:15:32 GMT 2026) Configuration file: /tmp/hostapd-ath0.conf Configuration file: /tmp/hostapd-ath1.conf Configuration file: /tmp/hostapd-ath20.conf rfkill: Cannot open RFKILL control device l2_packet_init: ioctl[SIOCGIFINDEX]: No such device Failed to open l2_packet interface for vlan bridge ACS: Automatic channel selection started, this may take a bit ACS: Offloading to driver rfkill: Cannot open RFKILL control device l2_packet_init: ioctl[SIOCGIFINDEX]: No such device Failed to open l2_packet interface for vlan bridge ACS: Automatic channel selection started, this may take a bit ACS: Offloading to driver rfkill: Cannot open RFKILL control device l2_packet_init: ioctl[SIOCGIFINDEX]: No such device Failed to open l2_packet interface for vlan bridge ACS: Automatic channel selection started, this may take a bit ACS: Offloading to driver nss_build_bypass is called with guardian-configured configurator: got event(guardian-configured, ) wan, sysevent received: phylink_wan_state Restarting nfqrecv service... nl80211: ACS Results: PFreq: 6115 SFreq: 6155 BW: 160 VHT0: 47 VHT1: 0 HW_MODE: 2 EDMGCH: 0 ath20: ACS-COMPLETED freq=6115 channel=33 wpa_driver_nl80211_set_key: ifindex=24 (ath20) alg=3 addr=0x54d6a684 key_idx=1 set_tx=1 seq_len=0 key_len=16 key_flag=0x1a wpa_driver_nl80211_set_key: ifindex=24 (ath20) alg=4 addr=0x54d6a684 key_idx=4 set_tx=1 seq_len=0 key_len=16 key_flag=0x1a ath20: interface state UNINITIALIZED->ENABLED ath20: AP-ENABLED ath20: IEEE 802.11 driver had channel switch: freq=6115, ht=1, vht_ch=0x0, offset=1, width=5 (160 MHz), cf1=6185, cf2=0 ath20: CTRL-EVENT-CHANNEL-SWITCH freq=6115 ht_enabled=1 ch_offset=1 ch_width=160 MHz cf1=6185 cf2=0 dfs=0 configurator: got event(firewall-status, starting) configurator: got event(firewall-status, started) nss_build_bypass is called with lan_dhcp_client_change Checking HW version...XB ===> RESET 25 GPIO for DIVO usb power configurator: got event(lan_dhcp_client_change, add 48:65:ee:15:3f:37 10.234.1.129 trudeautop br0 '') configurator: got event(firewall-status, starting) configurator: got event(firewall-status, started) nl80211: ACS Results: PFreq: 2437 SFreq: 2417 BW: 40 VHT0: 4 VHT1: 0 HW_MODE: 1 EDMGCH: 0 ath0: ACS-COMPLETED freq=2437 channel=6 wpa_driver_nl80211_set_key: ifindex=22 (ath0) alg=3 addr=0x54d6a684 key_idx=1 set_tx=1 seq_len=0 key_len=16 key_flag=0x1a wpa_driver_nl80211_set_key: ifindex=22 (ath0) alg=4 addr=0x54d6a684 key_idx=4 set_tx=1 seq_len=0 key_len=16 key_flag=0x1a ath0: interface state UNINITIALIZED->ENABLED ath0: AP-ENABLED ath0: IEEE 802.11 driver had channel switch: freq=2437, ht=1, vht_ch=0x0, offset=1, width=2 (40 MHz), cf1=2447, cf2=0 ath0: CTRL-EVENT-CHANNEL-SWITCH freq=2437 ht_enabled=1 ch_offset=1 ch_width=40 MHz cf1=2447 cf2=0 dfs=0 Got a TERM signal, will terminate. Warning! nfqrecv encountered errors when doing recv(): Interrupted system call configurator: got event(firewall-status, starting) configurator: got event(firewall-status, started) killall: nfqrecv: no process killed start mcsd succeeded (Wed Feb 4 16:15:37 GMT 2026) 16.15.37.994082 MCSD plugin info : Initializing plugin manager configurator: got event(nfqrecv-status, stopped) nl80211: ACS Results: PFreq: 5180 SFreq: 5220 BW: 80 VHT0: 42 VHT1: 0 HW_MODE: 2 EDMGCH: 0 ath1: ACS-COMPLETED freq=5180 channel=36 wpa_driver_nl80211_set_key: ifindex=23 (ath1) alg=3 addr=0x54d6a684 key_idx=1 set_tx=1 seq_len=0 key_len=16 key_flag=0x1a wpa_driver_nl80211_set_key: ifindex=23 (ath1) alg=4 addr=0x54d6a684 key_idx=4 set_tx=1 seq_len=0 key_len=16 key_flag=0x1a ath1: interface state UNINITIALIZED->ENABLED ath1: AP-ENABLED ath1: IEEE 802.11 driver had channel switch: freq=5180, ht=1, vht_ch=0x0, offset=1, width=3 (80 MHz), cf1=5210, cf2=0 ath1: CTRL-EVENT-CHANNEL-SWITCH freq=5180 ht_enabled=1 ch_offset=1 ch_width=80 MHz cf1=5210 cf2=0 dfs=0 configurator: got event(nfqrecv-status, started) udhcpc (v1.19.4) started btsetup service btsetup: smart_connect::setup_status btsetup: Unconfigured mode and Peripheral role bluetoothd.init: /var/run/dbus created bluetoothd.init: dbus-daemon started state_machine entering READY Sending discover... combo_solid(uxpurple) pub_devinfo_status: Error: could not determine HOST_ADDR XB smart_connect, sysevent received: wifi-status started hcisetup: Enabled LE advertising pub_wlan_status: Error: could not determine HOST_ADDR configurator: got event(firewall-status, starting) btsetup[0] succeeded. configurator: got event(firewall-status, started) Sending discover... Sending select for 192.168.1.115... Sending select for 192.168.1.115... Lease of 192.168.1.115 obtained, lease time 43200 getting geoip information for 192.168.1.115 % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0curl: (7) Couldn't connect to server backhaul_switching status event default_router 192.168.1.1 received on backhaul_switching_mgr nss_build_bypass is called with ipv4_wan_ipaddr 2026-02-04 16:15:52: error : default_router unknown 2026-02-04 16:15:52: Usage: node-mode [ node-mode-start | node-mode-stop | node-mode-restart] lldpd event ipv4_wan_ipaddr 192.168.1.115 received. device_registration: Received event: wan-started DNSServiceProcessResult returned -65537 device_registration: Service started [/etc/init.d/service_ntpclient.sh] Set TZ default already done, ignore. Wed Feb 4 16:15:53 2026 xrac Device is not associated, exiting... data_uploader service started killall: mdns_lookup: no process killed killall: mdns_register: no process killed LookUpMaster call OK. mDNS lookup is on going... configurator: got event(wan-status, started) Device "br1" does not exist. br1 global address not available to delete lo global address not available to delete configurator: got event(firewall-status, starting) configurator: got event(firewall-status, started) Belkin ICC Cron job created Registering Service myrouter._http._tcp.local port 80 configurator: got event(ntpclient-status, starting) configurator: got event(ntpclient-status, started) Got a reply for myrouter._http._tcp.local.: Name now registered and active configurator: got event(firewall-status, starting) configurator: got event(firewall-status, started) LookUpMaster call OK. mDNS lookup is on going... delete unreachable and blackhole route ****:****:**:****::/62 dev lo Checking update.. 96 [fw.sh] fwup_checked_after_boot: 0 [fwupd] version: 1.1.12.216649 [fwupd] status details:"" [fw.sh] fwup_forced_update: 0 Entry tsmb tsmb-stop, 1 Entry tsmb tsmb-start, 1 Device "br1" does not exist. br1 global address not available to delete ip -6 addr del ****:****:**:****::1/64 dev lo RTNETLINK answers: File exists Device "br1" does not exist. br1 global address not available to delete ip -6 addr del ****:****:**:****::1/64 dev lo delete unreachable and blackhole route ****:****:**:****::/62 dev lo

OpenWrt bootlog

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014] [ 0.000000] Linux version 6.18.52 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.4.0 r36661-061397968d) 14.4.0, GNU ld (GNU Binutils) 2.46.1) #0 SMP Mon Sep 28 14:35:46 2026 [ 0.000000] Machine model: Linksys MR7500 [ 0.000000] OF: reserved mem: 0x0000000000060000..0x0000000000065fff (24 KiB) nomap non-reusable memory@60000 [ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable memory@40000000 [ 0.000000] OF: reserved mem: 0x000000004a100000..0x000000004a4fffff (4096 KiB) nomap non-reusable bootloader@4a100000 [ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable memory@4a600000 [ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable memory@4aa00000 [ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004fffffff (87040 KiB) nomap non-reusable memory@4ab00000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff] [ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a0fffff] [ 0.000000] node 0: [mem 0x000000004a100000-0x000000004a4fffff] [ 0.000000] node 0: [mem 0x000000004a500000-0x000000004a5fffff] [ 0.000000] node 0: [mem 0x000000004a600000-0x000000004fffffff] [ 0.000000] node 0: [mem 0x0000000050000000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s44248 r8192 d29480 u81920 [ 0.000000] pcpu-alloc: s44248 r8192 d29480 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=rootfs root=mtd:squashfs rootwait root=/dev/ubiblock0_0 [ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB [ 0.000000] software IO TLB: mapped [mem 0x000000005f4c0000-0x000000005f5c0000] (1MB) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479] [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.000000] arch_timer: cp15 timer running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000149] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000162] pid_max: default: 32768 minimum: 301 [ 0.004412] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.004424] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.014388] rcu: Hierarchical SRCU implementation. [ 0.014396] rcu: Max phase no-delay instances is 1000. [ 0.014695] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.015101] smp: Bringing up secondary CPUs ... [ 0.015773] Detected VIPT I-cache on CPU1 [ 0.015918] CPU1: Booted secondary processor 0x0000000001 [0x51af8014] [ 0.016650] Detected VIPT I-cache on CPU2 [ 0.016763] CPU2: Booted secondary processor 0x0000000002 [0x51af8014] [ 0.017549] Detected VIPT I-cache on CPU3 [ 0.017659] CPU3: Booted secondary processor 0x0000000003 [0x51af8014] [ 0.017736] smp: Brought up 1 node, 4 CPUs [ 0.017744] SMP: Total of 4 processors activated. [ 0.017748] CPU: All CPU(s) started at EL1 [ 0.017752] CPU features: detected: 32-bit EL0 Support [ 0.017757] CPU features: detected: CRC32 instructions [ 0.017807] alternatives: applying system-wide alternatives [ 0.018017] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.018272] Memory: 382220K/524288K available (9536K kernel code, 924K rwdata, 3096K rodata, 1024K init, 300K bss, 139068K reserved, 0K cma-reserved) [ 0.025368] posixtimers hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.025442] futex hash table entries: 1024 (65536 bytes on 1 NUMA nodes, total 64 KiB, linear). [ 0.025515] 29008 pages in range for non-PLT usage [ 0.025520] 520528 pages in range for PLT usage [ 0.027850] pinctrl core: initialized pinctrl subsystem [ 0.031993] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.032551] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.032589] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.032623] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.033013] thermal_sys: Registered thermal governor 'step_wise' [ 0.033074] cpuidle: using governor menu [ 0.033291] ASID allocator initialised with 65536 entries [ 0.039620] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/ethernet-pcs@7a10000 [ 0.039640] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/ethernet-pcs@7a00000 [ 0.039745] /soc@0/interrupt-controller@b000000: Fixed dependency cycle(s) with /soc@0/interrupt-controller@b000000 [ 0.039839] /soc@0/ethernet-pcs@7a00000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000 [ 0.039857] /soc@0/ethernet-pcs@7a10000: Fixed dependency cycle(s) with /soc@0/clock-controller@1800000 [ 0.044126] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/ethernet-pcs@7a10000 [ 0.044147] /soc@0/clock-controller@1800000: Fixed dependency cycle(s) with /soc@0/ethernet-pcs@7a00000 [ 0.063210] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.086135] SCSI subsystem initialized [ 0.086371] usbcore: registered new interface driver usbfs [ 0.086410] usbcore: registered new interface driver hub [ 0.086446] usbcore: registered new device driver usb [ 0.086751] qcom_scm: convention: smc arm 64 [ 0.089907] s2: Bringing 0uV into 725000-725000uV [ 0.089979] clocksource: Switched to clocksource arch_sys_counter [ 0.090991] l2: Bringing 0uV into 1800000-1800000uV [ 0.091137] qcom_rpm_smd_regulator remoteproc:glink-edge:rpm-requests:regulators: Supply for l2 (l2) resolved to itself [ 0.094316] NET: Registered PF_INET protocol family [ 0.094468] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.096968] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.096988] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.097010] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.097058] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.097195] TCP: Hash tables configured (established 4096 bind 4096) [ 0.097488] MPTCP token hash table entries: 512 (order: 2, 12288 bytes, linear) [ 0.097650] UDP hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.097682] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.098216] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.098253] PCI: CLS 0 bytes, default 64 [ 0.099781] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 0.100546] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.100554] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.103356] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.106835] qcom-qmp-usb-phy 78000.ssphy: supply vdda-phy not found, using dummy regulator [ 0.106990] qcom-qmp-usb-phy 78000.ssphy: supply vdda-pll not found, using dummy regulator [ 0.108066] qcom-qusb2-phy 79000.qusb: supply vdda-pll not found, using dummy regulator [ 0.108167] qcom-qusb2-phy 79000.qusb: supply vdda-phy-dpdm not found, using dummy regulator [ 0.111049] qcom-pcie 20000000.pcie: host bridge /soc@0/pcie@20000000 ranges: [ 0.111110] qcom-pcie 20000000.pcie: IO 0x0020200000..0x002020ffff -> 0x0000000000 [ 0.111138] qcom-pcie 20000000.pcie: MEM 0x0020220000..0x002fffffff -> 0x0020220000 [ 0.117411] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.121252] msm_serial 78b0000.serial: msm_serial: detected port #1 [ 0.121334] msm_serial 78b0000.serial: uartclk = 24000000 [ 0.121833] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 20, base_baud = 1500000) is a MSM [ 0.122300] msm_serial 78b1000.serial: msm_serial: detected port #0 [ 0.122410] msm_serial 78b1000.serial: uartclk = 1843199 [ 0.122821] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115199) is a MSM [ 0.122905] msm_serial: console setup on port #0 [ 0.122949] printk: legacy console [ttyMSM0] enabled [ 0.242103] qcom-pcie 20000000.pcie: iATU: unroll T, 8 ob, 8 ib, align 4K, limit 1024G [ 0.246481] msm_serial: driver initialized [ 0.479984] qcom-pcie 20000000.pcie: PCIe Gen.3 x1 link up [ 1.050656] qcom-pcie 20000000.pcie: PCI host bridge to bus 0000:00 [ 1.055808] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.061975] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.067520] pci_bus 0000:00: root bus resource [mem 0x20220000-0x2fffffff] [ 1.073772] pci 0000:00:00.0: [17cb:1003] type 01 class 0x060400 PCIe Root Port [ 1.080567] pci 0000:00:00.0: BAR 0 [mem 0x00000000-0x00000fff] [ 1.087746] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.093660] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.098858] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.105121] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref] [ 1.111940] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold [ 1.122274] pci 0000:01:00.0: [17cb:1104] type 00 class 0x028000 PCIe Endpoint [ 1.125885] pci 0000:01:00.0: BAR 0 [mem 0x00000000-0x001fffff 64bit] [ 1.133252] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.139481] pci 0000:01:00.0: 7.876 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8.0 GT/s PCIe x2 link) [ 1.145753] pci 0000:00:00.0: bridge window [mem 0x20400000-0x205fffff]: assigned [ 1.160158] pci 0000:00:00.0: BAR 0 [mem 0x20220000-0x20220fff]: assigned [ 1.167790] pci 0000:01:00.0: BAR 0 [mem 0x20400000-0x205fffff 64bit]: assigned [ 1.174606] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.181678] pci 0000:00:00.0: bridge window [mem 0x20400000-0x205fffff] [ 1.186883] pci_bus 0000:00: resource 4 [io 0x0000-0xffff] [ 1.193829] pci_bus 0000:00: resource 5 [mem 0x20220000-0x2fffffff] [ 1.199204] pci_bus 0000:01: resource 1 [mem 0x20400000-0x205fffff] [ 1.207943] pcieport 0000:00:00.0: PME: Signaling with IRQ 31 [ 1.212048] pcieport 0000:00:00.0: AER: enabled with IRQ 31 [ 1.216306] loop: module loaded [ 1.224804] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xac [ 1.226114] nand: Hynix H27S4G8F2EDA-BC [ 1.232721] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128 [ 3.732462] ------------[ cut here ]------------ [ 3.732499] nss_crypto_clk_src: rcg didn't update its configuration. [ 3.732542] WARNING: CPU: 1 PID: 1 at drivers/clk/qcom/clk-rcg2.c:136 update_config+0xac/0xc0 [ 3.742494] Modules linked in: [ 3.750904] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.52 #0 NONE [ 3.753862] Hardware name: Linksys MR7500 (DT) [ 3.761062] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 3.765406] pc : update_config+0xac/0xc0 [ 3.772258] lr : update_config+0xac/0xc0 [ 3.776424] sp : ffffffc080edba00 [ 3.780329] x29: ffffffc080edba00 x28: ffffff80031691b0 x27: 0000000000000001 [ 3.783550] x26: 0000000000000002 x25: 0000000000000000 x24: 0000000023c34600 [ 3.790668] x23: ffffff8002048c00 x22: 00000000016e3600 x21: ffffffc080bba110 [ 3.797786] x20: ffffffc080e1b2e8 x19: 0000000000000000 x18: ffffffc080d8e5d8 [ 3.804903] x17: 00000000ff804db2 x16: 0000000090e808f9 x15: 00000000000000ac [ 3.812021] x14: ffffffc080edb800 x13: 00000000ffffffea x12: ffffffc080de6580 [ 3.819139] x11: ffffffc080d8e5d8 x10: ffffffc080de65d8 x9 : 0000000000000001 [ 3.826257] x8 : 0000000000000001 x7 : 0000000000017fe8 x6 : c0000000ffffefff [ 3.833377] x5 : 0000000000057fa8 x4 : 0000000000000000 x3 : ffffffc080edb800 [ 3.840495] x2 : ffffffc080d8e508 x1 : ffffffc080d8e508 x0 : 0000000000000038 [ 3.847613] Call trace: [ 3.854720] update_config+0xac/0xc0 (P) [ 3.856981] clk_rcg2_configure+0x84/0x98 [ 3.861147] clk_rcg2_set_rate_and_parent+0x2c/0x44 [ 3.865054] clk_change_rate+0x7c/0x298 [ 3.869741] clk_core_set_rate_nolock+0x154/0x260 [ 3.873561] clk_set_rate+0x38/0x14c [ 3.878421] of_clk_set_defaults+0x234/0x4c0 [ 3.882068] platform_probe+0x38/0xa4 [ 3.886319] really_probe+0xbc/0x2bc [ 3.889879] __driver_probe_device+0x80/0x14c [ 3.893526] driver_probe_device+0x40/0xe8 [ 3.897779] __driver_attach+0x90/0x160 [ 3.901772] bus_for_each_dev+0x64/0xb8 [ 3.905505] driver_attach+0x24/0x30 [ 3.909323] bus_add_driver+0xe4/0x20c [ 3.913143] driver_register+0x68/0x124 [ 3.916703] __platform_driver_register+0x24/0x30 [ 3.920437] qca_ppe_driver_init+0x1c/0x28 [ 3.925297] do_one_initcall+0x50/0x210 [ 3.929289] kernel_init_freeable+0x270/0x2e4 [ 3.933022] kernel_init+0x20/0x140 [ 3.937535] ret_from_fork+0x10/0x20 [ 3.940834] ---[ end trace 0000000000000000 ]--- [ 4.270951] i2c_dev: i2c /dev entries driver [ 4.276175] sdhci: Secure Digital Host Controller Interface driver [ 4.276218] sdhci: Copyright(c) Pierre Ossman [ 4.281278] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.285942] qcom_rng e3000.qrng: TRNG support not detected [ 4.291980] clocksource: arch_mmio_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 4.296723] arch-timer-mmio b120000.timer: mmio timer running at 24.00MHz (virt) [ 4.310281] remoteproc remoteproc0: releasing wcnss [ 4.317487] NET: Registered PF_INET6 protocol family [ 4.321400] Segment Routing with IPv6 [ 4.324965] In-situ OAM (IOAM) with IPv6 [ 4.328541] NET: Registered PF_PACKET protocol family [ 4.332521] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.337634] 8021q: 802.1Q VLAN Support v1.8 [ 4.382134] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 4.382470] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 4.388260] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2 [ 4.394879] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 4.402527] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 4.410033] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 4.419164] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 675000 uV [ 4.426122] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 787500 uV [ 4.436107] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 850000 uV [ 4.445920] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 900000 uV [ 4.455749] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 571, quot_offset[ 7]= 0 [ 4.465533] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 755, quot_offset[ 7]= 180 [ 4.476383] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]= 851, quot_offset[ 7]= 95 [ 4.487323] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]= 919, quot_offset[ 7]= 65 [ 4.498552] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 4.501553] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xac [ 4.516019] nand: Hynix H27S4G8F2EDA-BC [ 4.522389] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128 [ 4.526301] 20 qcomsmem partitions found on MTD device qcom_nand.0 [ 4.533617] Creating 20 MTD partitions on "qcom_nand.0": [ 4.539821] 0x000000000000-0x000000180000 : "0:sbl1" [ 4.547296] 0x000000180000-0x000000280000 : "0:mibib" [ 4.551842] 0x000000280000-0x000000600000 : "0:qsee" [ 4.558832] 0x000000600000-0x000000680000 : "0:devcfg" [ 4.561129] 0x000000680000-0x000000700000 : "0:rpm" [ 4.566031] 0x000000700000-0x000000780000 : "0:cdt" [ 4.570850] 0x000000780000-0x000000800000 : "0:appsblenv" [ 4.575673] 0x000000800000-0x000000980000 : "0:appsbl" [ 4.582238] 0x000000980000-0x000000a00000 : "0:art" [ 4.586265] 0x000000a00000-0x000000a80000 : "0:ethphyfw" [ 4.591437] 0x000000a80000-0x000000b00000 : "u_env" [ 4.596645] 0x000000b00000-0x000000b40000 : "s_env" [ 4.601065] 0x000000b40000-0x000000b80000 : "devinfo" [ 4.645772] 0x000000b80000-0x000001380000 : "kernel" [ 4.653586] 0x000001380000-0x000005d80000 : "rootfs" [ 4.721103] mtd: setting mtd14 (rootfs) as root device [ 4.721450] mtdsplit: no squashfs found in "rootfs" [ 4.725193] 0x000005d80000-0x000006580000 : "alt_kernel" [ 4.737619] 0x000006580000-0x00000af80000 : "alt_rootfs" [ 4.805212] 0x00000af80000-0x00000b380000 : "sysdiag" [ 4.809318] 0x00000b380000-0x00001f080000 : "syscfg" [ 5.097510] 0x00001f080000-0x00001f580000 : "app_data" [ 7.451490] Aquantia AQR114C 90000.mdio-1:08: loading firmware version 'v5.6.5 Cybertan Divo 090221 14:43:44' from 'NVMEM' [ 18.865007] hwmon hwmon7: temp1_input not attached to any thermal zone [ 19.198538] cpufreq: cpufreq_policy_online: CPU0: Running at unlisted initial frequency: 799999 kHz, changing to: 864000 kHz [ 19.200653] remoteproc remoteproc0: wcnss is available [ 19.530392] qca-ppe 3a000000.ppe: configuring for fixed/internal link mode [ 19.530461] qca-ppe 3a000000.ppe: Link is Up - 1Gbps/Full - flow control off [ 19.710933] qca-ppe 3a000000.ppe lan1 (uninitialized): PHY [90000.mdio-1:00] driver [Qualcomm QCA8075] (irq=POLL) [ 19.790396] qca-ppe 3a000000.ppe lan2 (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL) [ 19.870516] qca-ppe 3a000000.ppe lan3 (uninitialized): PHY [90000.mdio-1:02] driver [Qualcomm QCA8075] (irq=POLL) [ 19.950518] qca-ppe 3a000000.ppe lan4 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8075] (irq=POLL) [ 19.960133] qca-ppe 3a000000.ppe wan (uninitialized): PHY [90000.mdio-1:08] driver [Aquantia AQR114C] (irq=POLL) [ 19.960990] qca-edma 3ab00000.edma eth0: entered promiscuous mode [ 19.970070] DSA: tree 0 setup [ 19.976326] ubi0: attaching mtd14 [ 20.379999] random: crng init done [ 20.404103] ubi0: scanning is finished [ 20.411576] ubi0: attached mtd14 (name "rootfs", size 74 MiB) [ 20.411617] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 20.416310] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 20.423098] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 20.429938] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0 [ 20.436718] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 20.442972] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1790606146 [ 20.450010] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 80 [ 20.459297] ubi0: background thread "ubi_bgt0d" started, PID 757 [ 20.460123] block ubiblock0_0: created from ubi0:0(rootfs) [ 20.474614] clk: Disabling unused clocks [ 20.480320] check access for rdinit=/init failed: -2, ignoring [ 20.483125] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 20.485368] Freeing unused kernel memory: 1024K [ 20.492384] Run /sbin/init as init process [ 20.496580] with arguments: [ 20.496584] /sbin/init [ 20.496589] with environment: [ 20.496593] HOME=/ [ 20.496597] TERM=linux [ 20.766369] init: Console is alive [ 20.766572] init: - watchdog - [ 21.299746] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 21.328628] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 21.341944] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 21.341992] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 21.347217] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000808000000010 [ 21.353932] xhci-hcd xhci-hcd.1.auto: irq 49, io mem 0x08a00000 [ 21.363380] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 21.369159] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 21.374725] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 21.382597] hub 1-0:1.0: USB hub found [ 21.388874] hub 1-0:1.0: 1 port detected [ 21.392826] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 21.396917] hub 2-0:1.0: USB hub found [ 21.404765] hub 2-0:1.0: 1 port detected [ 21.412339] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 21.413963] init: - preinit - [ 22.244626] qca-ppe 3a000000.ppe lan1: configuring for phy/qsgmii link mode [ 26.984083] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 26.984200] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 936 [ 27.022488] UBIFS (ubi0:1): recovery needed [ 27.119162] UBIFS (ubi0:1): recovery completed [ 27.119266] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 27.122533] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 27.130443] UBIFS (ubi0:1): FS size: 54091776 bytes (51 MiB, 426 LEBs), max 436 LEBs, journal size 2666496 bytes (2 MiB, 21 LEBs) [ 27.140324] UBIFS (ubi0:1): reserved for root: 2554887 bytes (2495 KiB) [ 27.151950] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 62B705CF-277D-4FB1-BB62-13255CB99A72, small LPT model [ 27.165786] mount_root: switching to ubifs overlay [ 27.175285] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 27.180506] urandom-seed: Seeding with /etc/urandom.seed [ 27.288595] procd: - early - [ 27.288716] procd: - watchdog - [ 27.845563] procd: - watchdog - [ 27.846292] procd: - ubus - [ 27.933998] procd: - init - [ 28.376616] kmodloader: loading kernel modules from /etc/modules.d/* [ 28.440295] urngd: v1.0.2 started. [ 28.504388] Loading modules backported from Linux version v7.2-0-g8d3ae59288f1 [ 28.504428] Backport generated by backports.git v5.15.58-1-198-g2580fa90cb79 [ 28.517749] NET: Registered PF_QIPCRTR protocol family [ 28.589788] PPP generic driver version 2.4.2 [ 28.591160] NET: Registered PF_PPPOX protocol family [ 28.601669] ath11k c000000.wifi: ipq6018 hw1.0 [ 28.601703] ath11k c000000.wifi: FW memory mode: 1 [ 28.637142] remoteproc remoteproc0: powering up wcnss [ 28.653544] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340 [ 29.557140] remoteproc remoteproc0: remote processor wcnss is now up [ 29.558994] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff [ 29.562606] ath11k c000000.wifi: fw_version 0x25008f8e fw_build_timestamp 2024-03-01 03:54 fw_build_id WLAN.HK.2.5.0.1-03982-QCAHKSWPL_SILICONZ-3 [ 29.563265] ath11k_pci 0000:01:00.0: BAR 0 [mem 0x20400000-0x205fffff 64bit]: assigned [ 29.584088] ath11k_pci 0000:01:00.0: enabling device (0000 -> 0002) [ 29.592388] ath11k_pci 0000:01:00.0: MSI vectors: 16 [ 29.597917] ath11k_pci 0000:01:00.0: qcn9074 hw1.0 [ 29.603118] ath11k_pci 0000:01:00.0: FW memory mode: 2 [ 29.796706] mhi mhi0: Requested to power ON [ 29.796769] mhi mhi0: Power on setup success [ 30.540004] mhi mhi0: Wait for device to enter SBL or Mission mode [ 30.597312] kmodloader: done loading kernel modules from /etc/modules.d/* [ 30.608430] ath11k_pci 0000:01:00.0: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff [ 30.608487] ath11k_pci 0000:01:00.0: fw_version 0x290b8862 fw_build_timestamp 2024-09-23 10:51 fw_build_id [ 31.115156] ath11k_pci 0000:01:00.0: htt event 48 not handled [ 33.104312] qca-ppe 3a000000.ppe lan1: configuring for phy/qsgmii link mode [ 33.260701] br-lan: port 1(lan1) entered blocking state [ 33.260750] br-lan: port 1(lan1) entered disabled state [ 33.264788] qca-ppe 3a000000.ppe lan1: entered allmulticast mode [ 33.270051] qca-edma 3ab00000.edma eth0: entered allmulticast mode [ 33.276603] qca-ppe 3a000000.ppe lan1: entered promiscuous mode [ 33.288619] qca-ppe 3a000000.ppe lan2: configuring for phy/qsgmii link mode [ 33.440592] br-lan: port 2(lan2) entered blocking state [ 33.440632] br-lan: port 2(lan2) entered disabled state [ 33.444668] qca-ppe 3a000000.ppe lan2: entered allmulticast mode [ 33.450240] qca-ppe 3a000000.ppe lan2: entered promiscuous mode [ 33.458616] qca-ppe 3a000000.ppe lan3: configuring for phy/qsgmii link mode [ 33.620742] br-lan: port 3(lan3) entered blocking state [ 33.620786] br-lan: port 3(lan3) entered disabled state [ 33.624823] qca-ppe 3a000000.ppe lan3: entered allmulticast mode [ 33.630508] qca-ppe 3a000000.ppe lan3: entered promiscuous mode [ 33.638761] qca-ppe 3a000000.ppe lan4: configuring for phy/qsgmii link mode [ 33.800666] br-lan: port 4(lan4) entered blocking state [ 33.800711] br-lan: port 4(lan4) entered disabled state [ 33.804752] qca-ppe 3a000000.ppe lan4: entered allmulticast mode [ 33.810528] qca-ppe 3a000000.ppe lan4: entered promiscuous mode [ 33.819834] qca-ppe 3a000000.ppe wan: configuring for inband/usxgmii link mode [ 34.469795] ath11k c000000.wifi: No regulatory rules available in the event info [ 34.469839] ath11k c000000.wifi: failed to extract regulatory info [ 34.477995] ath11k c000000.wifi: No regulatory rules available in the event info [ 34.482303] ath11k c000000.wifi: failed to extract regulatory info [ 34.692047] ath11k c000000.wifi: No regulatory rules available in the event info [ 34.692094] ath11k c000000.wifi: failed to extract regulatory info [ 34.700221] ath11k c000000.wifi: No regulatory rules available in the event info [ 34.704525] ath11k c000000.wifi: failed to extract regulatory info [ 34.846487] ath11k c000000.wifi: No regulatory rules available in the event info [ 36.572745] qca-ppe 3a000000.ppe lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 36.573221] br-lan: port 2(lan2) entered blocking state [ 36.579222] br-lan: port 2(lan2) entered forwarding state [ 39.531495] qca-ppe 3a000000.ppe wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 326.420796] ath11k_warn: 3 callbacks suppressed [ 326.420815] ath11k c000000.wifi: No regulatory rules available in the event info [ 326.424160] ath11k c000000.wifi: failed to extract regulatory info [ 326.433116] ath11k c000000.wifi: No regulatory rules available in the event info [ 326.437790] ath11k c000000.wifi: failed to extract regulatory info [ 432.965809] kmodloader: loading kernel modules from /etc/modules.d/* [ 432.968523] kmodloader: done loading kernel modules from /etc/modules.d/* [ 435.002877] kmodloader: loading kernel modules from /etc/modules.d/* [ 435.011259] kmodloader: done loading kernel modules from /etc/modules.d/* [ 435.662117] kmodloader: loading kernel modules from /etc/modules.d/* [ 435.666363] kmodloader: done loading kernel modules from /etc/modules.d/* [ 436.772119] kmodloader: loading kernel modules from /etc/modules.d/* [ 436.781750] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 436.781790] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 436.788863] kmodloader: done loading kernel modules from /etc/modules.d/*

Notes

GitHub issue:

https://github.com/openwrt/openwrt/issues/21835

Forum thread:

https://forum.openwrt.org/t/adding-support-for-linksys-mr7500/170721

Hardware info:

https://techinfodepot.shoutwiki.com/wiki/Linksys_MR7500

Table of Contents